Saltear al contenido principal


Unmatched Acquisition Flexibility

The T35689iu is the latest integrated OEM forensic bridge from Tableau. This product, available from all Tableau resellers, supports write-blocked acquisitions of up to eight different types of storage media: IDE, SATA, SAS, USB 3.0/2.0/1.1, and FireWire 800/400. No other hardware write-blocker available today can match the forensic imaging capabilities of the T35689iu.

The T35689iu mounts in one 5.25″ half-height drive bay at the front of a forensic workstation and connects to the host computer via a SuperSpeed USB 3.0 port.

As with all other Tableau products, firmware updates are easy to apply using the Tableau Firmware Update utility, which has been rewritten to support product firmware updates via USB. The T35689iu incorporates the exclusive Tableau «U» update button for secure and reliable management of product firmware updates.

Each T35689iu ships with a complete set of hard drive power and signal cables (TC2-8-R2, T4-8-R2, TC6-8, TC-USB3, and TC7-9-9). For integration into forensic workstations, USB 3.0 cables in various lengths are available for optional purchase.


Product Forensic SATA/IDE/SAS/USB/FireWire Combo Bridge: Tableau Model T35689iu
Connectors: Host side (Rear)
FireWire NOTE: This port is disabled in firmware dated Oct 18 2012 and later (TFU v6.98)
One FireWire 800 (9-pin, 1394B) connector
USB One USB 3.0 Type B (9-pin) connector
DC Input One 4-pin male Molex connector for input DC power
Connectors: Device, Write-Blocked (Front Panel)
FireWire One FireWire 800 (9-pin, 1394B) connector
USB One USB 3.0 Type A (9 pin, super/high/full/low speed) connector
SAS One SAS data connector
SATA One SATA data connector
IDE One 40-pin IDE data connector
DC Out One 4-pin 3M drive power connector (power to SATA, SAS, or IDE hard disk)
Power Controls power for devices connected to front panel
‘U’ (Update) Used to set T35689iu in Firmware Update mode
DIP Switch 4-position DIP switch configures user-selectable options
Other Features
Status LEDs 5 LEDs: Power ON, Device detected, Host connected, Write-block enabled, Drive activity
Factory Configuration Read only
USB Devices USB devices must conform to the USB Mass Storage Specification and more particularly must implement the Bulk Only Interface Protocol
SAS Devices SAS hard disk devices
SATA Devices SATA 1 or SATA 2 hard disk devices (SATA 3 devices will default to SATA 2)
IDE Devices Parallel ATA hard disk devices with LBA (Logical Block Addressing) support
Host Interface USB 3.0. Note: For the best USB 3.0 performance, ensure the latest host controller driver and BIOS update are applied.
Host O/S Windows XP/Vista/7/8/Newer, Macintosh OS X, most Linux distributions (note: Linux distributions have varying levels and quality of support for USB 3.0)
Physical / Environmental
Power 8.5 watts typical operating (not including hard disk)
Supply voltage (DC IN A/B) +5VDC @ 3A, +12VDC @ 3A (includes budget for hard disk)
Output voltage (DC OUT) +5VDC @ 1A, +12VDC @ 1A
Dimensions 5.75 in. (L) x 5.75 in. (W) x 1.625 in. (H)
Weight 12.06oz (342g)
Operating temperature range 0 to 55 degrees C (no airflow)
Storage temperature range -40 to 70 degrees C
Relative humidity Up to 90% (non-condensing)
Warranty One years parts and workmanship from date of purchase
Volver arriba